They are making several good pointers regarding A Step-by-Step Guide to Installing a Bathtub as a whole in this great article in the next paragraphs.
Installing a tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is conveniently available, the task can move rapidly; if you need to open up a wall surface to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and also embeded in the new one. See to it you have actually qualified on your own for the task and fit trying it. Rather than employing a service provider to take control of a halfway-completed task, it is better to think about using one prior to you begin. Opportunities are you might require a professional plumber to make tube connections.
This write-up will help you install a new bathtub in your shower room if you have already bought a brand-new bathtub and don't require to alter the setup of your previous supply of water pipes.
Your devices and also product list must comprise the following:
Getting ready for the Setup
First of all, the supporting framework provided with the bath needs to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the remaining water that will originate from the pipelines. Once the supply pipes have been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bath tub
Using the two wooden boards under its feet, place the bath tub in the needed placement. The wood boards are handy in evenly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water system as well as check all joints and brand-new pipework for leakages and also tighten them if necessary. Load the tub and also inspect the overflow outlet and also the regular outlet for leaks.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub ought to wait till the bath tub has been utilized a minimum of once as this will settle it right into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers are in location in between the faucet and the sink. Secure the tap in place with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to split a rigid seal, triggering the water to penetrate the wall between the bath and also the tiling, leading to problems with wetness and also feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to enable the motion experienced when the tub remains in use. The sealer can split fairly early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly offered on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about Installing A Bathtub? Give a remark further down. We'd be delighted to listen to your opinions about this blog posting. We hope that you come back again later on. I beg you take the opportunity to promote this blog posting if you appreciated it. I cherish reading our article about How to Install a Bathtub Yourself.
Get Quote Now